跳至正文

Packaging Coffee Beans: CO₂ Outgassing, One-Way Valves, and Bag Sizes

Freshly roasted beans release several liters of CO₂ per kilogram during the first few days—without a valve, the bag swells; without purging, the aroma oxidizes. This article presents degassing curves, bag sizes, and the appropriate machinery.

Table of Contents

Whole beans come with their own set of requirements

The market share of whole-bean coffee is growing in the DACH region by about 4 to 5% per year, and in the premium segment, it is growing faster than ground filter coffee. To meet this demand, roasters are seeking machinery that fulfills three requirements simultaneously: format flexibility ranging from 100-gram samples to 1-kilogram packages, integrated valve application, and reproducible low-oxygen bags. This article covers the product side—outgassing, formats, and the barrier. The mechanical engineering perspective on the same line is discussed in the article on Vertical form-fill-seal machine for coffee beans; the basics of valves in the article on Flavor Preservation for Coffee.

CO₂ outgassing dictates the schedule

Freshly roasted beans release 6 to 10 mg of CO₂ per gram of beans during the first 24 to 72 hours after roasting. The rate of release is not linear:

  • Round 60% of the CO₂ escape within the first 24 hours after roasting.
  • The remaining 40 % are spread out over the next 4 to 6 days.
  • A 250-gram package releases a total of up to 2.5 liters of CO₂.

If the bag is sealed without pressure equalization, excess pressure builds up: The bag visibly swells, and in extreme cases, the cross-seal may burst. There are two ways to solve this problem: Allow the beans to degas in a controlled manner for 12 to 48 hours before packaging—during which time some flavor compounds will escape—or, immediately after roasting and cooling, use Check valve packaging. The valve opens at a pressure of approximately 0.02 bar, allowing CO₂ to escape while retaining oxygen; for packages weighing 1 kg or more, two valves are installed in parallel to accommodate the larger volume of gas. The complete valve mechanism is included with the product Flavor Preservation for Coffee.

Four Bag Sizes and Their Roles

Format Typical capacity Characteristics Format Change
Doy-Pack (stand-up pouch) 250 g to 1 kg Industry standard, large print area, valve located at the top right of the seal edge 15 to 20 minutes
Quad-Seal Bags 500 g to 1 kg Premium block design, precise volume control, diagonal valve position 20 to 30 minutes
Block-bottom bags 1 kg Classic family-size package, easy to fold by machine 10 to 12 minutes
Side-gusseted bags 100 g Sample format with low material costs, up to 120 bags per minute. less than 10 minutes

Two design factors must be taken into account in the cost calculation: The bottom fold of the Doy-Pack increases material consumption by 12 to 15% compared to flat pouches, and the four seal seams of the Quad-Seal bag increase the seam length by about 40%—both factors must be included in the film cost calculation, which is the key driver for the item Reduce Film Costs covered in detail. A valve window in the film does not protrude into any of these seams: The valve position is specified in the recipe and is format-dependent.

Low in oxygen in a sealed bag

The target after sealing is less than 2% residual oxygen; in the premium segment, it is less than 1%. Without purging, the bag remains at 8 to 12%—thereby reducing the shelf life to 4 to 6 months. The target value is achieved through a N₂ purge line, which is fed into the open bag before cross-sealing. Nitrogen consumption increases with the package size: approximately 0.3 to 0.5 liters per 250-gram bag, 0.8 to 1.2 liters per 500-gram bag, and 1.5 to 2 liters per 1-kilogram bag. The immersion depth and flushing duration are stored in the recipe based on the format; the flushing process technology is explained in the article on Flavor Preservation for Coffee.

Materials: Aluminum vs. Mono-PE

  • PET/AL/PE (12/7/60 to 80 µm): The aluminum interlayer provides the strongest barrier (oxygen permeability below 0.5 cm³/m²·d) and is therefore the standard for a shelf life of 12 to 18 months. For dark roasts with a higher oil content on the bean surface, the high barrier is particularly beneficial because lipid oxidation on the surface would otherwise lead to flavor defects.
  • Kraft paper/AL/PE: A paper-like appearance for artisanal and organic brands with the same barrier level; the paper layer is more challenging to process and requires tighter web tolerances.
  • Mono-PE with EVOH: Recyclable in the PE stream; oxygen permeability of 2 to 3 cm³/m²·d—sufficient for a shelf life of 6 to 9 months for 250 g, but not yet for 18 months and 1 kg, because cumulative oxygen uptake over the long shelf life dominates the loss of flavor.

A transparent window in the center of the bag interrupts the aluminum layer; the barrier performance in this area deteriorates by a factor of about ten. If you want windows, design them to be small and flanked by full-surface cover printing.

Machine Side: VFFS with Valve Applicator

The standard line for whole beans is a Vertical filling and capping machine with three additional stations:

  1. Dosing via a linear scale with an accuracy of ±0.2 g; beans should not be placed on a screw conveyor, but rather on a weighing or vibrating feeder.
  2. Inline Valve Applicator: Valve material from the roll—cut, position, and weld in less than 1 second. One roll holds about 4,000 valves, and it takes 2 minutes to change the roll.
  3. N₂ Purge Station between dosing and cross-sealing, controlled based on the format.

The production rate is 40 to 80 bags per minute for the 250-g Doy-Pack; for the 1-kg format, 30 to 40 bags per minute is realistic; above that, the mechanical stress on the forming shoulder increases and maintenance intervals become shorter. Switching from 250 g to 1 kg involves changing the forming shoulder, web width, and scale division in under 20 minutes; all parameters, including valve position and immersion depth, are specified in the format recipe. For Quad-Seal Premium formats, a premade pouch line with a capacity of 35 to 60 pouches per minute is an alternative—a basic comparison is provided in the VFFS Guide. The overview of all formats and machine types begins in the Hub Packaging Coffee; the product page for the Coffee Packaging Machine groups the configurations.

For logistics purposes, a Euro pallet holds approximately 1,440 250-gram Doy-packs in 8 layers of 180 packs each (360 kg net weight); 1-kg block-bottom bags amount to 480 pieces and 480 kg. These values determine the design of the downstream palletizing and wrapping modules.

Frequently Asked Questions

Does every package of beans need a one-way valve?

Yes, with one exception: vacuum-sealed packages. However, vacuum sealing is uncommon for whole beans because the external pressure causes the beans to split, and cracked shells detract from their appearance. For Doy-Pack, Quad-Seal, and block-bottom packages, the valve is mandatory.

What is a realistic production rate for 1-kg packages?

30 to 40 bags per minute. Higher cycle rates require wider webs or double spools; at rates above 40 bags per minute, the load on the molding shoulder increases noticeably, and maintenance intervals are shortened accordingly.

Can the line be converted from 250 g to 1 kg?

Yes. The format change switches the mold shoulders, pouch web width, and dosing scale graduation in less than 20 minutes; the valve position, the immersion depth of the flushing lance, and the sealing temperature are specified in the format recipe.

Can recyclable single-material products replace aluminum?

For 250-gram packages with a shelf life of 6 to 9 months, yes—mono-PE with EVOH achieves 2 to 3 cm³/m²·d. For 18 months and 1 kilogram, aluminum remains the reliable barrier.

Is nitrogen purging required?

Recommended for all packages with a target residual oxygen level below 2%: Without purging, 8 to 12% remains in the bag, and the flavor retention drops to 4 to 6 months. For sample bags with a short shelf life, flushing can be omitted; for premium espresso, it is mandatory.

Related pages: Flavor Preservation for Coffee | Packaging Ground Coffee | Vertical form-fill-seal machine for coffee beans | Packaging Coffee: The Eight Formats


Request technical specifications and a quote for your production line. Please specify the product, bag size, and target output (bags/min.) – Request Technical Specifications and a Quote.

Picture of Evelyn

Evelyn

As an expert with 16 years of experience and over 300 completed projects, my goal is to provide you with the most suitable packaging solution right from the start.

Sign up for our newsletter

We select the most popular case studies from over 4,000 orders placed by our customers to help you find the right project for your success.

en_USEnglish