跳至正文

Sachets and Sustainability: Single-Material Design and Recyclability

The EU Packaging and Packaging Waste Regulation (PPWR) will make recyclability a requirement for market access starting in 2030. This article compares four strategies—single-material, paper, compostable films, and design-for-recycling—and explains what the transition means for manufacturing.

Table of Contents

Recyclability is becoming a prerequisite for market entry

Two factors are driving the debate on materials: the EU Packaging and Packaging Waste Regulation (PPWR), which sets binding recyclability and quota requirements (all packaging must be recyclable by 2030, with phased recycling targets for 2030 and 2040) and the retail sector’s procurement requirements, which are increasingly mandating single-material or paper packaging. The conflict is real: product protection and recyclability often clash in traditional composite materials. Four strategies bring both goals together—the relevant material properties are detailed in the article on the Sachet Materials, the product range of the sustainable packaging solutions shows the implementation.

What ”recyclable“ Actually Means

"Recyclable" means: capable of being sorted using NIR detection at European sorting facilities and recoverable within the target material stream. This gives rise to strict design rules:

  • Sorting efficiency of over 95% in the target stream (PE or PP)
  • EVOH barriers accounting for less than 5% of the total mass
  • No carbon black pigments (invisible to NIR), no PVC, and no PVdC
  • Elimination of contaminants—from labels to printing inks—to the extent technically feasible

A Comparison of Four Strategies

Strategy Material Proof Utilization Typical Applications
Single-material PE/PP 30 to 80 µm, a family of polymers CEFLEX Category A over 95% in the PE/PP stream Detergent, snacks, samples
Paper-based 40 to 60 g/m² with a dispersion-based sealant Sorting in the Paper Stream If the plastic content is less than 15%, it can be fully incorporated into the paper stream Tea, cereal, organic snacks
Compostable PLA, PHA, starch blends DIN EN 13432 Compost, not recycling Magazine inserts, short cycles
Design for Recycling Optimized existing networks RecyClass/CEFLEX Rating 70 to 80% achievable High-barrier products

Compostable does not mean recyclable: PLA films belong in the organic waste bin and act as contaminants in the plastic stream—the separation of material streams must be factored into the planning.

The Barrier Compromise

A single material alone offers little protection against oxygen. The solution is an embedded EVOH barrier layer below the 5% threshold: It reduces permeability to 1 to 5 cm³/m²·d and keeps the design recyclable within the PE stream—sufficient for most dry goods with a shelf life of less than 12 months. For 18 months and beyond, aluminum remains the barrier material; here, the solution lies in recycling-friendly design (vapor deposition instead of solid aluminum, thinner printed areas) rather than monomaterial construction. The comparison highlights the limitations of formats in terms of film consumption Sachet or bag.

What the machine adjustment entails

  1. Seal parameters: Each polymer window must be recalibrated—Mono-PE 140 to 180 °C, Mono-PP 160 to 180 °C, PLA 130 to 160 °C, with the smallest margin.
  2. Track voltage: When switching from stiffer composites to 30 to 40 µm of a single material, reduce the pre-stress values by 15 to 25%; otherwise, wrinkles will form at the mold shoulder.
  3. Preparation time: Thin films are more sensitive—realistically, add 5 to 10 minutes for each format change.
  4. Printing: Water-based paints adhere less well to mono-PE; corona treatment or a bonding agent should be included in the specifications.

The Vertical filling and capping machine processes these films using customized formulations; the sealing processes are covered in the article on Sealing Technology for Sachets.

Recycled material: Outer layer—yes, sealing layer—no

PPWR recycled content requirements can be easily met with sachets: recycled material in the outer layer as a printing substrate, and virgin material in the sealing layer. This ensures that seam strength remains unaffected, and food contact compliance testing can focus on the area that comes into contact with the product. Compostable films must be stored under hygroscopic conditions—below 50% relative humidity and at 15 to 25 °C; otherwise, seam strength decreases prior to processing.

Frequently Asked Questions

When does PPWR apply to sachets?

The regulation will take effect in phases; the key milestone is 2030—from that point on, only recyclable packaging may be placed on the market, as assessed according to the regulation’s “design for recycling” methodology. In 2040, quotas will tighten the requirements.

Is a single material enough for coffee?

For short-shelf-life products with a shelf life of up to about 12 months, an EVOH intermediate layer is sufficient; for products with a shelf life of 18 months or longer and requiring complete light protection, aluminum laminate remains the safest solution.

Is single-material packaging economically viable?

Standard in the industry for quantities of approximately 500,000 units per year and shelf-life requirements of up to 12 months; since this single-material product does not require lamination, the amount of film used is often less than that of comparable composite materials—the article on Reduce Film Costs.

Are paper sachets the better choice?

Yes, for eco-friendly dry goods—provided they have a medium barrier (80 to 150 cm³/m²·d) and short distribution cycles. Paper without an additional barrier is unsuitable for products containing fat or that are sensitive to moisture.

Related pages: Sustainable Packaging Solutions | Vertical Filling and Sealing Machine | Sachet Materials | Reduce Film Costs


Request technical specifications and a quote for your production line. Please specify the product, bag size, and target output (bags/min.) – Request Technical Specifications and a Quote.

Picture of Evelyn

Evelyn

As an expert with 16 years of experience and over 300 completed projects, my goal is to provide you with the most suitable packaging solution right from the start.

About Us

A solution for every need. From packaging and blow molding to filling, labeling, and packing, all the way to palletizing, Lintyco Pack offers solutions for every need.

Contact Us:008613868827095

Write to us:[email protected]

Catalog

Latest Posts

Hottest Product

Weekly Tutorial

Sign up for our newsletter

We select the most popular case studies from over 4,000 orders placed by our customers to help you find the right project for your success.

en_USEnglish